Bạn đang muốn tìm trung tâm bảo hành tủ lạnh LG chính hãng? Bạn không tìm thấy chỗ nào bảo hành hợp lý và giá tốt nhất? Nay điện lạnh Gia Khang là trung tâm uy tín bảo hành tủ lạnh Lg trên toàn quốc. Nếu quý khách đang sử dụng tủ lạnh LG mà bị lỗi, hãy liên hệ trực tiếp với trung tâm chúng tôi để được bảo hành tốt nhất. Đảm bảo sẽ bảo hành tận nơi. Cùng với đội ngũ nhân viên kỹ thuật hỗ trợ sửa chữa, chúng tôi sẽ mang đến một dịch vụ hoàn hảo nhất. Chúng tôi là đại lý ủy quyền của tủ lạnh LG trên toàn quốc. Một số mã lỗi, nếu quý khách gặp phải, hãy liên lạc với chúng tôi, để chúng tôi hỗ trợ quý khách: MÃ LỖI MÁY GIẶT CỬA TRƯỚC LG front load washer (fault codes) IE (water inlet error) Cause : Correct water level (246) is not reached within 8 minutes after water is supplied or it does not reach the preset wate r level within 25 minutes UE (imbalance error) Cause : The load is to small, the appliance is tilted, laundry is gathered to one side, non distributed things are put into the drum. OE (drain error) Cause: not fully drained within 10 minutes FE (over flow error) Cause: water is overflowing (water level frequency is over 213) When FE is diplayed the drain will pump out automatically. PE (pressure sensor error) Cause: the sensor switch assembly is out of order. dE (door open error) Cause: door not all the way closed, loose electrical connections at door switch and pwb assembly.The door switch assembly is out of order. Gasket on door maybe creased in. [-E (heating error) Cause: the thermistor is out of order. CE (oven current error) Cause: Main PWB assembly is out of order, Winding in the stator assembly is short circuited. LE (locked motor error) Cause: The connector (3-pin), male,white) in the motor harness is not connected to the connector. (3-pin,female,white) of stator assembly. Or the electrical contact between the connectors. (3-pin,male,white) in the motor harness and 4-pin,female,white connector in the main PWB assembly is bad or unstable. Or the motor harness between the stator assembly and main PWB assembly is cut (open circuit) Or the hall sensor is out of order/defective. bE (ball sensor error) Cause : Loose ball sensor connector,ball is out of order. This is displayed only when the start / pause button is first pressed in the OC test mode. EE (EEprom error) Cause: EEprom is out order. Displayed only when the start / pause button is first pressed in the OC test mode. PF (power failure) Cause : the washer experienced a power failure) E1 (leakage error) Cause : water leakage in hose connections. Water is leaked by damages. MÃ LỖI MÁY SẤY LG DRYER LG DRYER FAULT CODES: CL : Communciation error between boards. Replace both display board and control board. - MÃ LỖI TỦ LẠNH SIDE BY SIDE LG Refrigerator Er / FS Failure of freezer sensor : Cut or Short in circuit wire Er / rS Failure of Refrigerator sensor : Cut or Short in circuit wire Er / dS Failure of defrost sensor : Cut or Short in circuit wire Er / dH Failure of defrost mode: When defrost sensor doesn't reach 46f within 2 hours after starting defrost. Snapping of Defrost heater or Temperature fuse, pull out of connector. Er / FF Failure of BLDC Fan motor at freezer compartment. If there is no fan motor signal for more than 65sec in operation fan motor. Poor motor, hooking to wires of fan,contact of structures to fan,snapping or short of lead wires. Er / IF poor bldc motor connection,drive ic ,and TR Er / IS Short or Disconnection of icing sensor Er / CF Poor BLDC Motor connection,Drive IC,and TR Er/ CO Poor communication connection, Poor TR of Transmitter and Receiver Range, Refrigeration and washer Fault Codes are very much used these days on the newer Electonic Controls. This guide may be incomplete as manufactures use different parts on different models. This is a general guide to fault codes. We assume no responsibility for any action taken on your part as a result of using this guide. Consult your owners manual, as it may give the fault codes for your particular model. Contact a local servicer for repairs. If you didn't findTrung tâm bảo hành tủ lạnh lg tại tphcm luôn là nơi bảo hành uy tín và an tâm nhất, chúng tôi hy vọng những đóng góp của chúng tôi sẽ mang đến dịch vụ hài lòng nhất cho quý khách. MỌI CHI TIẾT XIN LIÊN HỆ : Hotline : 0909 306 267 TRUNG TÂM ĐIỆN LẠNH GIA KHANG VPĐD : 280/10B - Bùi Hữu Nghĩa - P.26 - Quận Bình Thạnh, TP.HCM Xem thêm: Địa chỉ trung tam bao hanh tu lanh hitachi tại tphcm
